How to Make a DIY Penis Pump At Home: Safety Guide

Would you like to make your own penis pump at home? If you’re on a budget or just really enjoy DIY projects, the idea of a homemade penis pump may be appealing. However, it’s important to think through the risks and benefits of this homemade solution before making one. In this guide, we’ll look at what penis pumps do, how to make a penis pump at home, and the risks of taking the DIY approach.

What is a penis pump?

A penis pump is a toy that can be used to help treat erectile dysfunction by increasing the size of the penis by creating a temporary vacuum effect around the penis. This vacuum effect draws blood into the penis for a swelling and hardening effect, which can be very helpful for those looking to improve their sexual performance or the appearance of their penis.

The appeal of homemade penis pumps

Professional commercial penis pumps are relatively expensive! For those who aren’t ready to invest in a high-end device, trying to make one at home first seems like a pretty attractive idea. However, while homemade toys may save you money in the short term, be sure to be aware of the potential risks of homemade toys before attempting this DIY project.

Materials you may need to make a homemade penis pump

DIY penis pumps at home require materials that can be purchased at a store that can achieve a vacuum effect. Here is a list of basic items you may need:

1. Cylinder

A clear and rigid tube that fits snugly around the penis. Many DIY devotees highly recommend using a plastic bottle, but be sure to pay attention to the strength of the material; an under-strength material will have difficulty withstanding the pressure, which can be a safety risk.

2. Pumps

Some hobbyists repurpose hand pumps from other devices (such as blood pressure monitors, etc.). You need something that can safely create a vacuum without causing bodily harm.

3. Sealing material

In order to create a good seal around the penis area, you will need some soft material. For example, rubber, silicone or even foam.

4. Valve

The valve is very important to control the amount of pressure inside the cylinder. A reliable valve will go a long way in avoiding physical injuries.

How To Make DIY Penis Pumps? A Step-by-Step Guide

Clear Water Bottle Method

Supplies needed

Clear water bottle with lid

Handheld vacuum pump for car

Plastic tubing

Sealant such as silicone

Drill bit

Thick sponges

Strong adhesive tape

Instructions

Drill: Drill a hole in the bottom of the water bottle the same size as the plastic tube. Place each drill bit into the end of the tube to find the right size drill bit. Then switch to the next larger drill bit.

Prepare the sponge: turn the water bottle over and draw the opening in the sponge. Set the sponge aside and work on it while the sealant dries.

Seal the tube: Simply remove the end of the plastic tube and apply about 1/4 inch or so of clear sealant to the outside.

Insert the tube: place the end of the plastic tube into the hole you drilled in the bottom of the water bottle. Keep them tightly fitted. Then, add an appropriate amount of sealant to the area where the tube enters to create an airtight seal.

Supporting the Tube: Keep the water bottle on its side and support the plastic tube so that it can seal straight into the hole. Allow to dry fully according to the instructions for your chosen sealant.

Cutting the sponge: return to the sponge you previously drew. And using scissors, simply cut the center sponge on the outside of the circle you drew earlier.

Make a donut shape: using scissors, cut out the center portion of the sponge to create a donut shape. Be sure to leave a thick ring as this will be able to cushion the opening of the penis pump.

Attach the sponge: slide the round sponge piece over the mouth of the water bottle. If it’s too tight, cut the circle off in one place to create a strip of sponge.

Tape the sponge: place the round sponge piece around the mouth of the water bottle and make sure there is enough room on each side of the sponge to fold it up. Next, cut a piece of sturdy duct tape.

Seal with tape: pull the ends of the sponge together and use the tape to hold the sponge ring securely in place. Be sure to fold the sponge over the edge of the water bottle when applying the tape. And smooth the tape evenly over the inside and outside of the bottle.

Finish sealing: continue to apply tape around the bottle so that they overlap and seal securely, and be sure to tightly fit the inside and outside of the water bottle as well.

Install the pump: slide the other end of the tubing onto your car’s hand pump. This way the DIY penis pump is ready to use.

TIP: If it’s hard to create suction, be sure to check that the holes you drilled are sealed and that you pressed and squeezed the opening of the pump hard enough to create a sufficient seal.

Soda bottle method

Supplies needed

Soda bottle

Fish tank siphon and tubing

Sealant such as silicone

Thick sponge

Strong adhesive tape

Drill bits

Sharp serrated knife

Instructions

Cutting the bottom: Use a serrated knife to cut off the bottom of an empty soda bottle. Always make sure that the bottom is cut as evenly as possible, this will affect the subsequent seal.

Drill the cap: remove the cap of the soda bottle and use the drill bit to drill a decent sized hole in the cap. Find a drill bit that will fit snugly inside by placing it inside the pipe and finding the right size drill bit. Then use the next larger drill bit.

Seal the pipe: Apply an appropriate amount of sealant to the outside of the pipe.

Inserting the pipe: slide the pipe into the hole in the soda bottle cap about 1/2 inch do superior. Then, apply an appropriate amount of sealant around the tube inside and outside of the cap. Let it sit for a while and let it dry according to the sealant’s instructions.

Prepare the sponge: after the cap has dried, pick up the soda bottle and place it on a large, thick sponge. And use a marker to draw lines around the opening.

Cut the sponge: use scissors to cut circles on the sponge along the drawn lines.

To make the donut: use scissors to cut out the inside of the sponge circle, shaped like a donut. Continue trimming in small increments until you can just slide the sponge circle completely to the bottom of the bottle.

Attach the sponge: Just slide the sponge circle over the opening at the bottom of the bottle and leave enough sponge to fold over and cover the entire rim. Next, cut a piece of tape strong enough so that it will seal against leaks.

Tape the sponge: Now, start folding the sponge and taping it firmly in place. Make sure that each piece overlaps the next and that the tape is firmly pressed down.

Complete the seal: continue to add tape to the cutouts in the bottle to create a seal.

Put the lid on: once the sealant on the lid and tube is dry, you can screw the lid back on and the homemade penis pump is ready to use.

Tip: If you are unable to create suction, check that the tube is sealed. You can also add more sealant and even seal the lid completely.

Alternatives to homemade penis pumps

If the cost of a high-end professional penis pump is too high, then consider these alternatives:

Less expensive commercial pumps

There are some relatively inexpensive penis pumps on the market that still offer good performance and safety features.

Exercises and supplements

Some people can achieve results with penis exercises or supplements, although the effectiveness of these methods varies from person to person.

Consult a doctor

If you are struggling with profile erectile dysfunction, a professional doctor may be able to recommend other specialized treatment options that are safer and more effective than homemade devices.

Final thoughts

While making your own penis pump at home may seem like a fun and affordable project, it’s also important to be properly aware of the risks involved.DIY penis pumps can cause potential bodily harm, and this, combined with the general lack of hygiene and safety features in DIY toys, makes it important to consider them carefully. If you really want to use a penis pump for the long term, invest in a professionally made and cost-effective penis pump that can give you a safer and more comfortable experience.